Anycubic Photon Printer Owners 造訪社團

原文網址 Gregor Ganglmair
2020-01-19 20:06:30

anyone have an idea why that happened?A ring was also seen during the print, but it went away with ipa

翻譯年糕

Óttar Freyr Einarsson
2020-01-19 20:09:03

Gregor Ganglmair
2020-01-19 20:10:08

Gregor Ganglmair
2020-01-19 21:07:06

Óttar Freyr Einarsson
2020-01-19 21:44:39

Óttar Freyr Einarsson
2020-01-19 23:30:02

Gregor Ganglmair
2020-01-20 01:03:46

原文網址 TJ Strickland
2020-01-19 20:04:54

Damn. Price of Grey 1L went up on Amazon from 39.99 to 45.99... :'(

翻譯年糕

David Martin
2020-01-19 20:24:19

Nat Sinclair
2020-01-19 20:55:42

Hector Alvarez
2020-01-19 20:58:29

TJ Strickland
2020-01-19 20:58:53

John Aldred
2020-01-19 21:01:43

Toby Kirkby
2020-01-19 21:08:51

John Aldred
2020-01-19 21:10:23

Logan Laborde
2020-01-19 23:02:00

Alek Idol
2020-01-20 12:30:05

Dan Gump
2020-01-20 22:06:23

原文網址 Casey Frank
2020-01-19 19:18:43

Is there an easier way to remove supports from og green resin miniatures? I keep breaking parts of the model when I clip the support

翻譯年糕

Gunnar Hannich
2020-01-19 19:21:28

Chris Holden
2020-01-19 19:27:22

Matt Houghton
2020-01-19 19:31:08

Casey Frank
2020-01-19 19:32:05

Ray Sears
2020-01-19 21:13:45

Jarin Udom
2020-01-19 22:27:37

Aaron McCommon
2020-01-19 22:27:43

Frank Martinez Jr
2020-01-20 00:06:39

Sean Guna
2020-01-20 00:28:52

Smith Hayward
2020-01-20 04:09:41

Bob Deblier
2020-01-20 04:23:12

原文網址 Steve Marshall
2020-01-19 19:17:46

I'm going to buy one of the new large format resin printers to work in conjuction with my Photon-S.

What does everyone reckon is the best? My budget is around $2000.

I'm looking at the Phrozen XL, Epax X10, Phenom and Transform. Any experiences with these? Any I'm missing out?

It's hard to decide.

翻譯年糕

Ben Wood
2020-01-19 20:15:53

Alex Vee
2020-01-19 20:19:29

Nipuna Gunarathne
2020-01-19 20:27:57

Benny Lu
2020-01-20 07:57:19

Felix Flauta Jr.
2020-01-20 11:41:50

Marc de Hoogh
2020-01-20 20:37:57

Blaine Tsukayama
2020-01-21 01:28:33

Gary Houser
2020-01-21 02:49:56

原文網址 Nigel Davies
2020-01-19 19:04:52

Print came out really well,
Except half way up there is a line and a small hole, what could cause this?

翻譯年糕

Craig Miln
2020-01-19 19:08:20

Bradley Hawkes
2020-01-19 19:11:04

Nigel Davies
2020-01-19 19:23:25

Jesper Hvid
2020-01-19 22:13:20

Zoltan Papp
2020-01-19 23:58:01

原文網址 Jure Slokar
2020-01-19 18:59:20

question: i just flashed epax firmware on to my photon, do i need to level it again?

翻譯年糕

Marcel Biermans
2020-01-19 19:58:55

Jure Slokar
2020-01-19 20:06:36

Janne Sjöström
2020-01-19 20:08:19

Jure Slokar
2020-01-19 20:27:02

Janne Sjöström
2020-01-19 21:16:36

Jure Slokar
2020-01-19 21:54:09

Marcel Biermans
2020-01-20 00:41:55

Richard Humble
2020-01-20 14:45:11

Bob Deblier
2020-01-20 15:27:51

原文網址 El Moreno de Cosio
2020-01-19 18:44:56

Diseño y Render en MatrixGold

- Impresora Anycubic Photon

- Resina Bluecast X10 + Sharpenizer

翻譯年糕

Xavi Ferrer
2020-01-19 20:47:36

原文網址 AlientheDavinci MrGrey IndigoAli
2020-01-19 18:41:20

原文網址 Jordan Harris
2020-01-19 18:27:53

I sometimes end up with a solid thick support like at this bear's face.. any reason why it is happening? I have been supporting with prusa, hollowing with chitubox and slicing with the photon software. So far I have only had this happen when I add the hollow step and in the future I think I'll start slicing with chitu as well if it works well! I have a photon s, and use elegoo grey standard

翻譯年糕