Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Martin Jewell
2020-03-18 22:47:52

Thought it was sticking to the fep well, a little too well it seems. The grub screw was tight too.

Shane McAlister
2020-03-18 22:52:10

delete that ball joint, its not worth the trouble it causes... go with a solid mount, or even print one of the options on Thingiverse. Ive got dozens of perfect prints using a solid printed mount.

Tim Moulton
2020-03-18 22:55:38

Shane McAlister dozens you say? I've put many hundreds through my ball joint bed and have never had it budge. So, user error?

Martin Jewell
2020-03-18 22:57:01

Tim Moulton maybe, it's the first time I've had the issue, I'm not worried, just thought I'd share it.

Shane McAlister
2020-03-18 22:57:05

Tim Moulton yes dozens, I've only purchased the Photon S in the last 2 weeks. The first thing I didn't like was the ball joint setup and grub screw arrangement.

Tucker Adams
2020-03-18 23:00:08

Apparently there can be a second grub screw in the slot, preventing it from actually tightening. May be worth looking at on yours

Noah Belveal
2020-03-18 23:00:37

It's not supposed to stick to the FEP.

Shane McAlister
2020-03-18 23:01:19

Mine arrived in this exact configuration, wouldnt allow me to level... thats when I broke the entire joint assembly down to see what the problem was, thats also when I decided to delete that setup.

Tucker Adams
2020-03-18 23:10:26

Shane McAlister granted I’ve only printed a total of 6 prints, mine hasn’t moved at all when I tightened it. I just got it level finally and it seems fine to me

Shane McAlister
2020-03-18 23:11:45

Tucker Adams yea I get that... like I said, after the disassembly of my new unit, I didnt like the design, so I updated it. Ive had zero failed prints.

John Coyne
2020-03-18 23:11:51

Shane which one on thingiverse did you use?

Ľuboš Kazík
2020-03-18 23:12:00

use this easy calibrator and fix bed
https://www.thingiverse.com/thing:3096818

Shane McAlister
2020-03-18 23:13:26

John Coyne https://www.thingiverse.com/thing:4021242

Merv Hinton
2020-03-18 23:14:02

Completely disassemble it and start again..I did..never had an issue..haven't relevelled..printing for 8+ months now.. https://www.youtube.com/watch?v=VdiNI_Xu6bI

Shane McAlister
2020-03-18 23:15:32

No complaints, was easy to level first time, hasn’t moved, no failed prints since I got the machine.

Tucker Adams
2020-03-18 23:21:19

Noah Belveal I’m still learning so I wanted to ask for clarification, build plate shouldn’t stick to fep but print should, right? The print pulling away is the “pop” sound? I’ve only had more of a peeling sound than a pop this entire time

Noah Belveal
2020-03-18 23:25:11

Good question. I think I see your misunderstanding.

The pop sound is good because it means the print is separating from the FEP. This is not to say that some sticking to the FEP is good, but that it is expected/unavoidable.

Jeff Greenfield
2020-03-19 01:23:21

My S did this, my OG never has. Take it apart, clean it, tighten everything down and you’ll be good to go.

Nathan Kopp
2020-03-20 03:48:14

you have gotten resin on the ball joint, had a similar issue

Peter Everett
2020-03-20 06:27:21

Is it the double screw issue from a while back?

You have to remove 1 screw, tighten the one under it and then you screw in the second one again to lock it in place

Rick Hanson
2020-03-21 19:52:16

Why do people keep repeating this crap? There's only supposed to be one grub screw to lock the build plate. If there are two, it's an assembly error from the factory.

原文網址 Martin Jewell
2019-10-17 12:06:11

Next question for you lovely people, what ultrasonic cleaners do you recommend? And, do you just use water in them or some other chemical?

翻譯年糕

Olivia Couture
2019-10-17 12:08:48

Olivia Couture
2019-10-17 12:10:22

Stephen Lewis
2019-10-17 12:13:48

James Long
2019-10-17 12:17:07

Olivia Couture
2019-10-17 12:17:59

Jared Davis
2019-10-17 12:24:11

Lee Perry
2019-10-17 13:10:27

原文網址 Martin Jewell
2019-10-17 10:26:17

Is there a slicer that orients models for optimal printing? I have a lot to learn and would like to minimize mistakes ( if I can). Is there a slicer that orients models for optimal printing? I have a lot to learn and would like to minimize mistakes ( if I can). 翻譯年糕

Paul Yanzick
2019-10-17 10:35:10

Martin Jewell
2019-10-17 10:41:49

Scott Pavlich
2019-10-17 11:28:45

Martin Jewell
2019-10-17 11:34:44

Hervé Pariente
2019-10-17 12:44:28

Hervé Pariente
2019-10-17 12:44:56

DJ Brookshire
2019-10-17 12:52:43

Minghua Kao
2019-10-17 13:22:57

Mack Whillz
2019-10-17 13:57:46

Ivan Adhi R
2019-10-17 14:16:25

Savio Ku
2019-10-17 15:17:02

Bartek Skórski
2019-10-17 15:28:36

Tim Moulton
2019-10-17 16:24:07

Sander Freitas
2019-10-17 16:40:13

Gergely Jávor
2019-10-17 17:14:23

Mano Doro
2019-10-17 17:44:08

Joe Eckert
2019-10-17 18:12:33

Chase Wichert
2019-10-17 19:54:01

Scott Hurd
2019-10-17 21:50:28

Marcio Yukio Takeda
2019-10-17 21:56:32

Martin Jewell
2019-10-18 08:12:18

Martin Jewell
2019-10-19 02:24:11

Szymon Buhajczuk
2019-10-19 05:06:26

Adrian M. Neville
2019-10-19 07:08:37

Marcio Yukio Takeda
2019-10-25 10:38:04

原文網址 Martin Jewell
2019-10-17 09:51:10

Ok, so, set up and first print went brilliantly. Realised I didn't have some IPA, and living in rural Saskatchewan it's not easy to find so I had to settle for rubbing alcohol ( ultrasonic cleaner is on order now). Anyway it cleaned up ok and is now curing under my UV lamp. Super happy with my purchase.

翻譯年糕

Paul Hail
2019-10-17 09:54:00