Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Verity Filipow
2020-03-26 19:21:05

Hey guys, this is still very much a work in progress, but I need some advice! I'm making a dragon doll and I've sculpted some elastic ball joints for its legs. There is also a top part to this leg which is not pictured. Anyway, I was wondering if you think using the 3D print on the actual doll would be strong and durable enough to do? I kind of dread the thought of moulding and casting these (there are holes running through the inside of the top and bottom part of the leg to allow for the elastic).

My question: what resin is strong enough to be able to use this as is without moulding and casting? And any advice on painting/pigmenting the resins?

EDIT: I'm using a Photon!

Thanks! Hope everyone is safe and well!:)

翻譯年糕

Sander van Deijl
2020-03-26 19:23:53

Any ABS-like resin would do fine I think ? ??

Verity Filipow
2020-03-26 19:25:46

Great! Any in particular that you'd recommend for the Photon?

Sander van Deijl
2020-03-26 19:27:48

Verity Filipow I have only used elegoo ABS-like grey, I’m very pleased with that one

Rose Stumpwater
2020-03-26 19:28:17

One thing folks have done with similar dolls in brittle material is to not make the bar from (in this case) 3d printed resin but instead leave or drill a hole and insert a very strong wire- basically a small metal bar epoxied into place so you can stri ng quite tightly for good posing, but without any worry you're going to break the bar.

I'd print from a material as close to the finished colour as you can and then paint with model paints or excellent quality acrylic and use a sealant, avoiding painting the ball joints if you can (as it will tend to chip and flake with wear). Check out some of the awesome full repaints of Monster High dolls on Youtube for inspiration. I highly recommend this channel: https://www.youtube.com/channel/UCitKV0ebZVbtU2nIPihDGMQ

Verity Filipow
2020-03-26 19:28:49

Okay thank you! I will have a look:)

Joseph Kason
2020-03-26 19:29:30

A mix of resins might be in order, here. Siraya Tenacious mixed with an ABS-like resin should do the trick.

Verity Filipow
2020-03-26 19:29:36

Oh fantastic! Thank you so much for all this!

Verity Filipow
2020-03-26 19:29:54

Fantastic, thank you so much for the advice!:)

Joseph Kason
2020-03-26 19:31:33

You may have to experiment a bit with ratios...usually not a straight 50:50 mix. And exposure times will be different, too. Run your exposure test on any mix you settle on before printing.

Verity Filipow
2020-03-26 19:31:59

Awesome, thanks for the tip:)

Kat Schulz-Booth
2020-03-26 20:00:05

What sort of range of movement do you want from your BJD? If you only want limited posing, light stringing and a little experimenting with exposure times would be worth the time.

Verity Filipow
2020-03-26 20:04:07

Moderate to limited posing. It's for a client, and I've stressed that these things are fragile and mainly for display only!

Kat Schulz-Booth
2020-03-26 20:05:59

Then I would play with the wall thickness and exposure times. Which resin do you normally use?

Jennifer Tallman
2020-03-26 20:13:47

I'm a fan of ApplyLabWork mSLA grey resin. It has twice the tensile strength than Anycubic and equivalent resins.

Verity Filipow
2020-03-26 20:46:54

Currently still getting through the anycubic green I have but willing to switch!

Neal Conway
2020-03-26 21:41:35

As stated above: Anycubic Resin is not good for tensile use.

Richard Tyler Jr
2020-03-27 08:35:54

A lot of people have been printing the bjd dragon from myminifactory. They hold up pretty good from what I've been told. Gonna try printing my own when the resin gets here.

Kat Schulz-Booth
2020-03-27 09:39:35

Give the green a go...will the BJD be painted? If so, just go with the resin you're use to, if it holds up strength-wise.

Jamie Masotti
2020-03-27 14:21:59

Yes, I've printed dolls just fine and they last and Havent broken

Mika Gruszka
2020-03-27 15:15:11

What is abs?

Sander van Deijl
2020-03-27 15:27:12

Mika Gruszka a kind of plastic

Verity Filipow
2020-03-27 18:10:07

Do you have a different brand you'd recommend instead?

Verity Filipow
2020-03-27 18:10:31

Which resin were you using?

Neal Conway
2020-03-27 18:24:53

Not that I've used but people on the Internet seem to recommend Siraya Blu as being one of the better ones.

Siraya claims to have printed a hook with it and hung a 20kg off it, summat you definitely couldn't do with the Anycubic Basic . . .

t's fairly expensive, though, at $50.00+ IF you can find it.

Verity Filipow
2020-03-27 18:25:36

Yeesh, okay. I'll have a look, maybe I'll find some over here in the UK. Thanks!:)

Neal Conway
2020-03-27 18:29:09

Verity Filipow Ah, I'm UK too. Ebay sellers are knocking it out @ £50... for 500ml!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

Verity Filipow
2020-03-27 18:33:56

Holy shit! I've just had a look... so insane.. I think I'll try an ABS like resin. Maybe that's a better shot right now.

Jamie Masotti
2020-03-27 22:44:28

I have been using elegoo ABS like resin

Verity Filipow
2020-03-28 22:29:08

Sorry just saw this. Yes, I'll be painting it. I'm going to try that elegoo abs like grey, as that's closer to the actual painted colour anyway!

Kat Schulz-Booth
2020-03-29 10:53:10

Good luck! And let me know how you go? BJDs are a hobby for me and if I can make it cheaper, yay.

Verity Filipow
2020-03-29 16:19:00

Will do! Thanks!

原文網址 Verity Filipow
2020-01-22 07:49:50

So after the 3rd time I tried printing with my photon, it started making this lovely sound once switched on. Lasts for about 30 seconds, then stops, and you can hear the fan run normally. Is this something I should be worried about?

所以第三次嘗試用我的光子列印後, 一旦開啓就開始製作這個可愛的聲音. 持續大約30秒, 然後停下來, 你可以聽到風扇正常運行. 這是我該擔心的嗎?

· 查看原文 · 為此翻譯評分

Thrall Hood
2020-01-22 07:53:35

Michael Power
2020-01-22 07:54:07

Jeremiah Chetwood
2020-01-22 07:55:04

George Bulte
2020-01-22 07:56:10

Verity Filipow
2020-01-22 07:58:24

Quinn Mehling
2020-01-22 08:48:25

Simon Wilson
2020-01-22 08:55:52

Glen Jones
2020-01-22 09:16:24

Sean Proctor
2020-01-22 09:56:55

Otto Rey
2020-01-22 12:15:10

Verity Filipow
2020-01-22 15:51:09

Gabrielle Underhill Lucas
2020-01-23 00:12:11

Ricciardetto Standen
2020-01-23 08:53:03

David Vh Goetz
2020-01-25 13:49:33

Patricia Rodríguez Torroba
2020-01-26 05:15:12

原文網址 Verity Filipow
2020-01-20 15:12:39

Argh, failed again. It's also really squishy.

AC Black resin
Exposure time 8s
Bottom layers 50s (3 layers)

What would cause it to be really soft and squishy still-as well as look melty and misaligned? I'm really certain my build plate is perfectly flat. Thanks for the help in advance- totally new to all of this!

翻譯年糕

Reggie Grahita Adhyatmaka Djatni
2020-01-20 15:15:02

Kristy Therrien
2020-01-20 15:22:57

Michael Power
2020-01-20 15:23:35

Verity Filipow
2020-01-20 15:24:39

Verity Filipow
2020-01-20 15:24:59

Reggie Grahita Adhyatmaka Djatni
2020-01-20 15:28:33

Pablo Coralio Ballester Pla
2020-01-20 15:29:18

Michael Power
2020-01-20 15:30:03

Stefan Giudici
2020-01-20 15:32:41

Verity Filipow
2020-01-20 15:32:48

Verity Filipow
2020-01-20 15:33:25

Verity Filipow
2020-01-20 15:37:24

Pablo Coralio Ballester Pla
2020-01-20 16:02:38

Pablo Coralio Ballester Pla
2020-01-20 16:03:57

Verity Filipow
2020-01-20 16:09:52

Nipuna Gunarathne
2020-01-20 16:21:00

Ivan Antharon Antalec
2020-01-20 17:27:44

Milton Maxson
2020-01-20 18:56:52

Rachit Modi
2020-01-20 19:39:53

Verity Filipow
2020-01-20 20:51:38

Aaron McCommon
2020-01-20 21:47:10

Mike Fatchett
2020-01-21 01:45:30

Julius EM
2020-01-21 13:39:53

Simon Wilson
2020-01-22 00:58:44

原文網址 Verity Filipow
2020-01-20 02:19:37

Hi all, first time printer here... I've set everything up this afternoon, and am using the Anycubic Black resin that came with my printer. I've used Chitubox to set it up using the settings from the google docs. I set:

Exposure Time: 7.0

Bottom Exposure Time : 90.0

and left everything else as is.

Started out well and made it about 45% done, and it looks like it's snapped off right at the base. I'm a total newbie to this, so any help is much appreciated! One variable I think is that it's quite chilly in the room with the window open for ventilation. Is there anything else I should be looking at?

Thanks!

翻譯年糕