Anycubic Photon Printer Owners 造訪社團

原文網址 Richard Syuge
2019-11-15 00:15:00

I tried to print some halo: ground command models. The bases came out perfectly, but 2 of the models failed to print, however the strange part is the supports printed just fine. Could this be contact diameter, of contact depth? I used the same settings for the models as the bases.

翻譯年糕

Simon Booth
2019-11-15 00:59:33

原文網址 Daniel Nollen
2019-11-14 23:45:42

My last print. Stalker Figure 1/35 scale, anycubic orange.

翻譯年糕

RIcardo Castillo
2019-11-15 00:09:08

Daniel Nollen
2019-11-15 00:13:06

Darren Ng
2019-11-15 15:59:59

原文網址 Nick Chicone
2019-11-14 23:44:37

Does anyone have tips on getting a model that has been printed flat on the build plate off? The scrapers I've got from my photons are all tore up. Thanks!

翻譯年糕

Eric Pribish
2019-11-14 23:46:31

Scott Pavlich
2019-11-14 23:47:04

Hugh Jeriolas
2019-11-14 23:47:04

Derek Reihe
2019-11-14 23:47:37

Blake Roney
2019-11-14 23:48:45

Eric Pribish
2019-11-14 23:49:00

Eric Wilfreesboro
2019-11-14 23:49:52

Joel Mendoza
2019-11-14 23:50:28

Zena Andreou
2019-11-14 23:52:32

Francis X Benz
2019-11-14 23:52:47

Stefan Giudici
2019-11-14 23:58:54

Joey Pruitt
2019-11-15 00:02:11

Ethan Williams
2019-11-15 00:03:29

Ironi R Johnson
2019-11-15 00:07:54

Jim Nelson
2019-11-15 00:27:12

Nick Chicone
2019-11-15 00:28:44

Chris Edrington
2019-11-15 00:36:13

Alex Dodge
2019-11-15 00:44:00

Simon Wilson
2019-11-15 00:46:40

Francis X Benz
2019-11-15 00:49:06

Joey Pruitt
2019-11-15 00:58:41

Simon Wilson
2019-11-15 01:03:49

Joe Lewis
2019-11-15 04:59:16

Polly Jackson
2019-11-15 05:13:52

Peter Ede
2019-11-15 05:25:14

原文網址 Montri Tong Sroymukda
2019-11-14 23:19:17

Castable resin with photon ... 30 micon

翻譯年糕

原文網址 Stephen Ross
2019-11-14 23:08:00

Doing a few test on joints and moving parts that connect and am looking for a strong resin to see how they hold up, needs to be relatively cheep as this is just a test and it might not work. Any suggestions?

翻譯年糕

Ric Watts
2019-11-14 23:14:09

Stephen Ross
2019-11-14 23:21:23

Ric Watts
2019-11-14 23:50:33

Stephen Ross
2019-11-15 00:15:52

原文網址 Paweł Szymiczek
2019-11-14 22:44:15

I am looking for the most precise resin for printing small stuff. I go advised, that HARZ Model is very good, but the shrinkage is bigger than Anycubic resin. Can share your experience?

翻譯年糕

原文網址 Shane Plagmann
2019-11-14 22:38:00

I can get small prints to come out fine, but for some reason I cant get the bigger prints to stick to the surface. Any suggestions?

翻譯年糕

David N. Amis
2019-11-14 22:45:10

Shane Plagmann
2019-11-14 23:10:18

David N. Amis
2019-11-14 23:11:58

Scott Schwoppe
2019-11-15 01:26:17

Rick Driftmyer
2019-11-15 11:37:45

Bogdan Preda
2019-11-15 15:03:02

原文網址 Kalia Herbststurm-Fyrstin
2019-11-14 22:12:35

Daniel Hoke
2019-11-14 22:14:45

Kalia Herbststurm-Fyrstin
2019-11-14 22:21:26

Ryan Pennington
2019-11-14 22:29:59

Simon Leclerc
2019-11-14 22:33:40

Justin Leone
2019-11-14 22:50:49

Kalia Herbststurm-Fyrstin
2019-11-14 23:54:19

Kalia Herbststurm-Fyrstin
2019-11-14 23:59:03

Brian Alexander
2019-11-15 00:27:59

Kalia Herbststurm-Fyrstin
2019-11-15 00:45:55

原文網址 Daniel Worden
2019-11-14 21:46:03

Hello all! Maybe somebody can clue me in to what the hell is going on? I’m getting successful prints, but at the base of the print where it’s closer to the print bed, It seems to fuse with the skate and or the support. Leaving a chunk I have to sand off. Although it’s not a huge issue...... it’s damn annoying. Andy ideas?

翻譯年糕

Jure Slokar
2019-11-14 21:51:27