Anycubic Photon Printer Owners 造訪社團

原文網址 Joseph Bushen
2019-03-03 07:40:16

Hi Folks,
Does anyone have settings for Monocure Gunmetal grey at below 30 microns? I'm printing 6mm scale models and so need the finest layer height possible. (I've checked the resin table but that didn't have settings for under 30 microns)

Many thanks :)

翻譯年糕

Fred Breton
2019-03-03 07:43:25

Katherine Dewey
2019-03-03 11:24:15

Sen Kun
2019-03-03 12:11:46

Joseph Bushen
2019-03-03 21:05:34

Joseph Bushen
2019-03-04 04:03:35

Joseph Bushen
2019-03-04 04:03:59

Fred Breton
2019-03-04 06:10:52

Fred Breton
2019-03-04 06:58:48

Sean Poeschl
2019-03-05 00:15:40

Joseph Bushen
2019-03-05 01:25:30

Sean Poeschl
2019-03-05 01:26:25

Joseph Bushen
2019-03-05 01:26:37

原文網址 Christopher Ashworth
2019-03-03 07:25:05

Came out perfectly now sitting in pride of place amongst one of my alien shelves

翻譯年糕

Michael M Thompson
2019-03-03 07:32:13

Michael Zinski
2019-03-03 11:35:04

Dani Rose
2019-03-03 15:04:31

Christopher Ashworth
2019-03-03 15:16:33

Christopher Ashworth
2019-03-03 15:17:23

Jon Kelly
2019-03-03 23:07:04

Michael Zinski
2019-03-04 00:36:10

原文網址 Rafael Anthony Acevedo
2019-03-03 07:03:44

Hey all - printing a ring. It's just a green lantern ring for a friend, but I am unsure of the best orientation for supports. Thoughts?

翻譯年糕

Dustin Skye
2019-03-03 07:47:21

Brandon Kennedy
2019-03-03 08:11:15

Dustin Skye
2019-03-03 08:12:41

Brandon Kennedy
2019-03-03 08:13:35

原文網址 Vinicius Silva
2019-03-03 06:36:40

Leonardo Delgado
2019-03-03 11:15:38

原文網址 David Nicholls
2019-03-03 06:32:21

Just about to purchase and print something from Gamebody

https://www.gambody.com/3d-models/futurama-bender

I Intend to print the FDM parts so I can print as big as possible - how much of an issue of resin shrinking - are we talking fixable/fileable and not noticeable.

翻譯年糕

原文網址 Gabriel Joel
2019-03-03 05:44:41

Does anyone know where I can purchase replacement build plate and replacement vat?Preferably in USA Does anyone know where I can purchase replacement build plate and replacement vat?Preferably in USA 翻譯年糕

Che Fielding
2019-03-03 05:49:21

Robert Silvers
2019-03-03 05:49:57

Rob Klingberg
2019-03-03 08:46:15

原文網址 Timothy Cann
2019-03-03 05:43:28

I’ve been using my Anycubic Photon for about six weeks, and frankly: I love it!!! I purchased the printer to make small parts for my HO model train layout, with plans to make operational parts for rolling stock, and scenic components. The detail is fantastic, and I’ve been able to print extremely small parts that meet requirements. Here is a representative set of parts already in use:

The first time I printed I followed tje user manual’s instructions including emptying, filtering and pouring leftover resin into the bottle. The amount of effort it takes to remove, clean and cure the parts each time takes some getting used to, but is not all that hard or time consuming. But I find the amount of work it takes to return the unused resin back into the bottle to be another matter. After the first use I decided to leave the resin in the vat against everything I can see on the website and on the Photon Facebook user group.
Here’s how. I purchased a metal box with lid and built foam inserts so the vat could be safely placed inside. This box is not light-tight so I keep it in a drawer that is not exposed to sunlight.

I’ve had no resin clouding… none. Using this method setting up for a new print is also a breeze. If I were to build another box, I would seal the corners and put a gasket round the top to seal it a bit more so that were there to be a spill inside, no resin would end up outside the box.

翻譯年糕

Robert Maefs
2019-03-03 05:46:19

Luis Filipe Mata
2019-03-03 06:00:08

Guido A. Mandorf
2019-03-03 06:59:57

Susan Sioux Mercer
2019-03-03 07:04:19

Chris Crute
2019-03-03 07:14:13

Sen Kun
2019-03-03 07:20:21

Marcus Como
2019-03-03 07:29:17

Scott Avis
2019-03-03 14:29:30

Jure Slokar
2019-03-04 02:49:20

GaryAnji Smith-Lambeth
2019-03-05 05:31:31

Sen Kun
2019-03-05 05:58:31

原文網址 Hans De Jong
2019-03-03 05:21:53

Hello, I have upgraded my command line program to trim the edges of images in a photon file. It can now be controlled with a GUI. An appimage file that should run on most Linux systems is available in the releases section:

翻譯年糕