Anycubic Photon Printer Owners 造訪社團

原文網址 Joel Ligeiro
2019-02-02 17:28:56

Hey. Anyone tested this one?
https://ameralabs.com/shop/amd-3-led/

翻譯年糕

Nikko Liadopoulos
2019-02-02 21:35:04

原文網址 Mario Reinh
2019-02-02 16:42:45

as promised from now in red

翻譯年糕

原文網址 Casper Kirketerp-Helenius
2019-02-02 16:42:17

Hi guys. I just Got my Photon a week and a half ago, and it has almost printed non-stop since. Most of the printed stuff is very good but I’ve seen some strange results that I wonder is any of you can explain. I will add the models as comments and would appreciate any help or direction, but overall I use the same setting for all models yet with different issues and results. Thanks a lot in advance. Casper

翻譯年糕

Casper Kirketerp-Helenius
2019-02-02 16:46:08

Casper Kirketerp-Helenius
2019-02-02 16:49:02

Casper Kirketerp-Helenius
2019-02-02 16:51:49

Susan Sioux Mercer
2019-02-02 16:53:12

Casper Kirketerp-Helenius
2019-02-02 16:54:28

Michael Chai
2019-02-02 16:56:35

Casper Kirketerp-Helenius
2019-02-02 16:57:12

Casper Kirketerp-Helenius
2019-02-02 16:58:09

原文網址 Michael Chai
2019-02-02 15:45:23

Think this the smallest I ever print, 1:75 bar stool, and that’s 0.05 layer heights not even the limit yet ?

翻譯年糕

Craig Cooper
2019-02-02 16:48:53

Michael Chai
2019-02-02 16:50:25

Michael Tennent
2019-02-03 01:55:47

Michael Chai
2019-02-03 08:42:03

Michael Tennent
2019-02-03 11:07:34

Michael Chai
2019-02-05 10:50:26

原文網址 Fernando Gómez Galloso
2019-02-02 14:12:12

Is it true??

這是真的??

· 查看原文 · 為此翻譯評分

Robert Silvers
2019-02-02 14:18:08

Erik Jonathan Gonzalez
2019-02-02 14:25:58

Robert Silvers
2019-02-02 14:30:09

Chris Hunt
2019-02-02 14:40:36

Chris Hunt
2019-02-02 14:45:33

Alex Vee
2019-02-02 17:27:07

Nick Williams
2019-02-02 17:42:12

Kelly Sealey
2019-02-02 18:01:20

Nick Williams
2019-02-02 18:08:59

Kelly Sealey
2019-02-02 18:14:01

Ivan Antharon Antalec
2019-02-02 18:24:36

Derek Reihe
2019-02-02 20:42:40

Paul Harker
2019-02-02 22:09:14

Ivan Antharon Antalec
2019-02-02 22:12:30

Derek Reihe
2019-02-02 22:15:37

Ivan Antharon Antalec
2019-02-02 22:16:28

Matt Mason
2019-02-02 22:27:32

Richard Shapiro
2019-02-03 00:51:45

Richard Shapiro
2019-02-03 00:52:10

Jack Sweek
2019-02-03 02:22:52

原文網址 Andrey Khudiakov
2019-02-02 14:00:31

Hello to all! Which resin is the least stinking? Which of the less stinky ones can be treated with water? Share your stench control experience. Thanks.

翻譯年糕

原文網址 Cameron Ramoly
2019-02-02 13:32:03

Ok, so typically as soon as someone says "my print didn't stick to the plate" the answer is "sand the buildplate" and yes there are a few other thingsthat affect it. But my prints have never had this problem. If something fails it's always been something i've done with the supports or such... Until just now. So... Seeing as how this isn't a new setup, and the buildplate has never needed sanding and that's not something that wears down. Should I sand it anyway?
I've also had the thought that it may have been too cold. It's around 40F in my garage. I did keep the resin in the house so it was warm, but the plate was cold. Could there be an interaction there?
Thanks in advance, You guys are always the best.

翻譯年糕

Stephen Lewis
2019-02-02 13:37:34