Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Bernie Santen
2020-02-26 19:55:30

Someone should make a
SMELL CHART
OF RESINS
Maybe A-Z how bad
And 1-10 how strong
A=flowers , bouquets cakes
Z=I want to rip out my nasal passage and throw up at the same time
1= not detectable
10=even my army surplus gas mask is melting

翻譯年糕

Vinicius Silva
2020-02-26 20:00:05

John Aldred
2020-02-26 20:01:48

Merv Hinton
2020-02-26 20:11:24

Vinicius Silva
2020-02-26 20:12:32

Scott Wolfs
2020-02-26 20:30:14

Tyler Vins
2020-02-26 20:33:46

Merv Hinton
2020-02-26 20:42:41

Micheal Ashton
2020-02-26 21:18:40

Kevin Blewitt
2020-02-26 21:20:18

Merv Hinton
2020-02-26 21:24:47

Merv Hinton
2020-02-26 21:26:42

John Vickers
2020-02-26 21:38:59

Alex M Cruz
2020-02-26 21:48:32

Merv Hinton
2020-02-26 21:53:27

Niall Forrester
2020-02-26 21:57:18

Ronald Smith
2020-02-26 21:58:41

Merv Hinton
2020-02-26 22:04:44

Merv Hinton
2020-02-26 22:06:11

原文網址 Bernie Santen
2020-01-28 21:23:13

OK i am old, 48 years as a bench jeweller. trying to prove you CAN teach an old dog new tricks.

Ok I did the sample cube, followed all the instrctions .. CAME OUT FANTASTIC. Made it small to save time..

Today i tried a ring..after 2 HOURS i could finally see under the build plate ( i put a bit too much resin in) and there was nothing there :(

I think that when i levelled the plate using the piece of paper method , i was over cautious?? with a 0.1mm down it was too tight and then 0.1mm up it was too loose.. I left it loose as i didnt want the Z to move down too far and break something.. When i clean out the tray tank the starting raft was attached to the plastic film.. Do you think that is why it didnt work . the build plate didnt lower enough to let the raft attach ??

Ive attached my 3 screen shots just in case i am doing somthing else glaringly obviously wrong..

would appreciate any one help if you dont mind please..

好吧, 我老了, 作為一個長椅珠寶48年. 試圖證明你可以教一條老狗新把戲.

好吧, 我做了樣式立方體, 跟著所有的插圖.. 出來太棒了. 讓它小, 節省時間..

今天我嘗試了一個戒指.. 2個小時後, 我終於可以看到了(我放太多樹脂), 那裡甚麼都沒有 :(

我想我用紙張方法把盤子放在板上時, 我太小心了?? 0.1 mm的0.1 mm, 太緊了, 然後0.1 mm up.. 我離開了因為我不想z移動太遠了, 打破一些東西.. 當我清理托盤箱時, 起始船被附在塑料膠片上.. 你覺得這就是為什麼它不起作用的原因嗎? "我是一個真正的??

我附上了我的3張螢幕截圖, 以防萬一我做其他事情顯然是錯的..

如果你不介意的話, 會感謝任何人幫忙..

· 查看原文 · 為此翻譯評分