Hi all, I've been working with this printer for over a week now, and I haven't had any luck. I've been FDM printing since 2011, but so far resin has proven to be frustrating.
So far I haven't had any successful prints. Every print gets a few layers in and sticks to the FEP. I've leveled the build plate many times using both the paper and Reed method, replaced the FEP (ensuring the film is removed)
I've disassembled, cleaned and re-assembld the build plate.
My build plate appears to have a tiny cup. I can just barely see light a steel machinists ruler is placed upon it.
I've tried to print the rook, and the birdcage From
https://pinshape.com/items/23778-3d-printed-bird-cages
. Both have been flat to the build plate. Should I be tilting/supporting these prints?
In addition to sticking to the FEP, I see a skin of resin around the part, and some loose partially cured resin floating in the vat. Checking the UV light and display, it looks like the patterns are being shown correctly.
I have also tried various settings, though I've only used the green which comes with the printer.
My settings for this print were:
Layer Height: 0.05
Bottom layer count: 10
Bottom Exposure Time: 80s
Regular exposure time: 15s
Light off delay: 1s
Bottom Light off Delay 5s
Everything else is standard from Chitubox.
I did run the print through the validator. It found a few island higher up the cage and repaired them.
If you look at the image showing the front of the build plate, the gap is larger on the right side. This plate is level in this photo. I'm not sure, but it looks a bit like my whole Z rail has a slight tilt - note the image showing the top of the rail. I'm not sure if I can use the shell of the printer as a reference here.
So Heeeelp - can anyone suggest what I should do to get a successful print?
翻譯年糕
Peter Jarvie
2019-08-23 04:06:03
J.R. Moore
2019-08-23 04:07:14
Valentine Catacarté
2019-08-23 04:09:00
Joshua Collins
2019-08-23 04:09:05
Adam Fabio
2019-08-23 04:17:55
Peter Jarvie
2019-08-23 04:21:11
Sean Croteau
2019-08-23 04:21:20
Handrez Pintubola
2019-08-23 04:32:18
Melecio Guzman
2019-08-23 04:44:13
Adam Fabio
2019-08-23 04:44:34
Adam Fabio
2019-08-23 04:47:25
Adam Fabio
2019-08-23 04:49:52
Melecio Guzman
2019-08-23 04:50:54
Melecio Guzman
2019-08-23 04:53:53
Melecio Guzman
2019-08-23 04:56:23
Christopher Anderson
2019-08-23 05:26:45
Adam Fabio
2019-08-23 05:26:50
Adam Fabio
2019-08-23 05:28:09
Handrez Pintubola
2019-08-23 05:34:28
Jarrod Schulte
2019-08-23 05:42:38
Melecio Guzman
2019-08-23 05:43:13
Melecio Guzman
2019-08-23 05:43:56
Valentine Catacarté
2019-08-23 06:44:32
Valentine Catacarté
2019-08-23 06:44:56
Spencer Kleinhans
2019-08-23 06:55:07
Stefan Giudici
2019-08-23 06:55:36
3D Scanning Guy
2019-08-23 06:57:56
Peter Ede
2019-08-23 07:05:11
Andrew Gott
2019-08-23 07:16:49
Jarrod Schulte
2019-08-23 07:56:52
Adam Fabio
2019-08-23 10:50:32
Adam Fabio
2019-08-23 11:21:51
Hugh Jeriolas
2019-08-23 12:55:14
Hugh Jeriolas
2019-08-23 12:58:46
Melecio Guzman
2019-08-23 12:59:18
Joe Eckert
2019-08-23 18:26:53
Loris Venegoni
2019-08-23 18:47:10
Stephen Farrell
2019-08-23 19:45:29
Gary Houser
2019-08-23 20:46:23
Christopher Anderson
2019-08-24 06:41:15
Soo Kang
2019-09-26 23:22:45
