Anycubic Photon Printer Owners 造訪社團

I really like Poly Juice water washable by filaments.ca.

Anycubic Eco has much less odor.
Also adding the filter helps a lot

Tell me more about the filter. Still new to 3D resin printing.

Elegoo gray is much better. Also Dragonresin gray.

Comment to follow

Is that the plant based Elegoo gray? Or the regular?

Tell her to stay out of the garage on print days.

Matthew Beauchamp
Regular is much less odorous.
I haven’t tried the plant based.
I hear the water washable is good.

Anycubic green is one of the smelliest resins. Kinda brittle too

Monocure Rapid 3D is definitely lighter on the odour than the Anycubics, but when I had the printer at work my boss still complained about it. I may just have no smell....

I found the IPA smell was also strong, trying water washable resin now.

IMO Anycubic Red have very tiny smell. But green and black smells awful. Without ventilation you can't sit with printer in room.

Matthew Beauchamp I've installed 3M filter with an additional duct in my Photon S.
https://www.thingiverse.com/thing:3591774


Also I've read about the success with DeStinkyNator a couple of times in the group.

https://www.thingiverse.com/thing:4007108

Get the anycubic plant based eco resin. It has virtually no smell and there's no difference from the standard resins as far as detail goes

Pues elegoo gris lavable 0 olores ?? dentro de casa ?

Hi, you have Ifun 3120W low odor https://lesresines3d.fr/....../45--standard-rigid...... ?

Alexandra Print you atr manufacturer?

Saša Sinek no reseller

Time for a new wife.

Elegoo resins barely smell at all. I'm using esun at the moment and that also doesn't have much of a smell.

I also use an expensive resin called Nextdent model ochre. It's a dental resin and has no Smell at all. £240 a litre though so might be a bit much just to get rid of the smell

Forget to take off the plastic?

Or spacing may be off if you have a glass protector on the screen.

I dont have a screen protector on and i for sure took the plastic off

Following, because, same here. No protective sheet. Print time went from 7.5 seconds to 13. Same everything except FEP

Which screen did you buy to replace your old one?

https://www.ebay.com/....../2560x1440-LCD....../184099653038

Gregory Thompson that one

Michael Paulick i changed my fep just to see if it fixed it and nothing I feel your pain

Wes Shawshank Crain it claims to be an Anycubic brand in the description. I was thinking if it was non-brand that it could possibly be filtering too much light. Hope you get it worked out

That’s awesome. Does it have a stand?

Brian Wulff nah I need to make one for it

Tucker Adams is it able to stand on its own? Orrr

Brian Wulff nope lol

wicked... :)

What is this from? Is it a original character?

James Capps Storm Javelin from Anthem

Beautiful that mate. Can I ask how many parts you were able to get it down to? ?

Rich Harrison 6 parts total. It came broken down from the designer

Tucker Adams good stuff. Love the paint work. Are you on Instagram?

Rich Harrison I am not, I should get one put together though. Need to think of a name for it lol

Tucker Adams let me know when you do ?

Im modeling them one at a time..

Adrian Jewell look amazing. I would love to print ur keys for my personal collection

Probably there was a residue of a print left there on the FEP.

the screen or the screen protector ? if it's the protector you can replace it if you carefully remove it from the screen

Zena Andreou can you buy replacement protectors?

yes. the protector is separate from the screen anyway.

Is this it?


https://www.google.com/....../item/32920911654.html

yes. make sure you can separate the one you have from your screen though. Worth having a spare screen at home as well, just in case

Got it. I have a screen on order but I’ll try to keep the one I have alive if I can replace the glass. Thanks!

I have to Buy a new screen for my Photon due to a massive leak that destroyed my screen. Do I have to buy a Screen protector as well as a screen? Or does the new screen come with one?

unless stated otherwise, they come separately. Worth getting them both

I think they have one, the eco-resin.

oh, cool. have you used it?

I have not, not yet.

They released an announcement that said they will not make a water washable resin because people will flush the water down and it really isn't safe to run off into the environment. So they decided to just look past that option

They have eco resin which is said to be biodegradable. They still say to use ipa but I have heard slme people say they can use water and soap. I am very new to printing so I have yet to get a fully successful print but I was soooo close yesterday lol. (Using the eco resin)

https://m.facebook.com/groups/1194619320682708?view=permalink&id=1933977470080219

ah, ok. i wasn't planning on washing the waste down the drain. You just get lots more life out of your ipa wash

Thanks, i'll have to give it a go. which one are you using at what settings?

Chris Jeanneret so as I said I am still new. Just did my first print a couple days ago. But i did the max settings it said on the bottle especially for the base layers as I was having adhesion issues.
So i think it was 80s for the base and then 8..for the rest. I believe i was printing at .05mm layer height. I can't remember all the details but again I have yet to get a fully successful print.
Had some supports fail and some missed layers leaving gaps. So still working on learning the designing and slicing.

Arianne Aucoin are you using the photon validator to check and auto-fix unsupported islands? i use the auto supports in prusa slicer then export the plate with supports, Open in chitu and slice. then open the file in photon validator and auto fix... I've found that is a pretty good way to cover most bases... that's if you don't want to spend ages supporting everything individually.

Chris Jeanneret i just did the auto supports for now. I will have to figure out how to even find unsupported islands ? ?‍♀️
I really donxt know what i'm doing yet. Was just gifted the printer recently so trying to swim in the deep end here. But the eco resin was the resin I got since it's biodegradable and has less odour.

Arianne Aucoin download a program called photon file validator. that will check over your sliced file and fix a load of islands for you with a click of a button.great video for it attached. https://www.youtube.com/watch?v=b3wFEdN7TqQ&t=2s

Chris Jeanneret amazing thank you!!! :)

Is there I way I can specifically request that they don't?

Not been able to get hold of any ipa so just rinsed my print in warm soapy water, probably not the perfect solution but works fine whilst I learn the ropes. Saw a YouTube video where they used cleaning products like Mr Clean and Mean green and seemed to work better than ipa. See if I can find the video and add a link. https://youtu.be/tnGasVwkgMk

I’d rather see all the companies that are making it now stop...willing to bet there’s people already washing it down drains.

Scott Pavlich to that's my concern

Penn Davies I’m pretty sure it’s not water soluble anycubic said they won’t make that

Fair.

You still use ipa to clean water washable resin? But why its water washable... i do t use ipa anymore...

Same can probably be said for the regular resins. Stupid is Stupid.

What did you clean the vat with now we can’t get IPA?

Most of the resin was poured out so just used a tissue to wipe and warm soapy (fairy liquid) water again with a tissue to wipe clean now left to dry.

Thank God I had already bought about 10 large bottles beck when I first got my printer. Still have 5 left