• #maker+t=market
  • COSPLAY 3D 建模
  • 3D列印服務
  • 1
  • 2
  • 3

Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Gabi Ras
2020-03-24 22:17:29

I noticed recently that my buildplate is wiggly! I leveled the plate using the paper method and made sure that I tighten the bolt on the top properly. But this did not resolve the issue. If anything the plate is even more wiggly now! I don't understand, what do I need to tighten to solve this??

My prints are getting ruined RIP ?

SOLVED: Take it all apart, clean with IPA, and put it back together. Worked like a charm. Thanks everyone for the help!

翻譯年糕

Ric Watts
2020-03-24 22:19:16

Did you get resin inside the ball joint?

Mourni Tenchou
2020-03-24 22:19:28

you probably got resin into the ball joint.

Disassemble the printhead, clean out the inside with IPA, reassemble. I had to do that a bunch cause i tend to overfill my vat. If that happens, its not a big issue.

Lorenz Steinke
2020-03-24 22:20:17

So I did, too. Worked fine.

Ric Watts
2020-03-24 22:22:15

Also take the 4 screws out and detach the top portion. Underneath that is 3 screws in a triangle pattern. If those go loose it will wobble.

Ric Watts
2020-03-24 22:22:35

Ian Gill
2020-03-24 22:25:14

Nooooooo! Don't do anything with the four screws yet. Take the grub screw out that is supposed to tighten the build plate. Now put the Allen key back in the hole and there's a very good chance you have another one in there. That's the one you tighten. The one you've taken out is a spare.

James Turner
2020-03-24 22:27:05

There are actually 2 set screws on top. The set screw you loosen and retighten to level the plate has another underneath it. Remove top one,level plate,tighten bottom screw,replace and tighten top screw

Gabi Ras
2020-03-24 22:27:06

Oh I see, I always tried my best to not overfill my vat. To my knowledge I never did. But thanks for the insight, I know what to do now! :)

James Turner
2020-03-24 22:28:49

No,its not a spare Ian Gill ...its a double lock setup. Both are needed to insure it doesnt come loose

Gabi Ras
2020-03-24 22:29:11

So i did take the grub screw out and the screw inside the hole is not something I can tighten or loosen. This is the photon s btw

Mike Johnson
2020-03-24 22:35:01

Mourni Tenchou and use blue lock-tight on the screws that should not be coming loose

Gabi Ras
2020-03-24 22:39:55

You mean this screw inside? I already tried turning it with an Allen wrench but it doesn't work, there's no opening for the wrench to be inserted into

Jeffery Nelson
2020-03-24 22:44:18

I had this problem and found that the set-screw had broken in half and any attempt to tighten it was only tightening the top half down onto the bottom half.

Gabi Ras
2020-03-24 22:49:14

I took it apart and am cleaning everything

Bastian Dietert
2020-03-24 23:02:12

Print the „More Easy Bed Leveller“ equipped with 4 Ball pen Springs.
Pur a paper on the Screen , move Home , Set Z , tighten screws and you are Fine !

Gabi Ras
2020-03-24 23:10:20

Hey everyone thanks for the help! The problem is SOLVED. I took it apart, cleaned with IPA and put it all back together.

Marco Dieckhoff
2020-03-24 23:32:15

Ric Watts if you are cleaning resin from it - use gloves!

(if this is reassembly after thorough cleaning, never mind)

Ric Watts
2020-03-25 00:09:36

Marco Dieckhoff stock photo from the net. Not my hands ? i don’t open the door without gloves

Nathan Kopp
2020-03-27 00:01:44

was going to say resin in the ball joint. happens way to often with me lol


原文網址 Gabi Ras
2020-02-28 07:50:33

Hi everyone, I searched for this error but could not find it anywhere. It was NOT my goal to print this hollow rectangle, I just wanted to print a brain. Where the hell did this come from??

This is the second time this happens to me and I really have zero idea why. I think maybe a faulty stl or something? Last time it happened I literally printed the same file again and it came out perfect. Any suggestions are welcome

Let's take a moment of silence for the effort that are required when cleaning this up. Rip all that resin. Rip my build plate. Rip the FEP. It takes a lot of strength to remove this useless piece of resin.

大家好, 我搜尋了這個錯誤, 但在任何地方都找不到. 列印這個空洞矩形不是我的目標, 我只想列印一個大腦. 這到底是從哪裡來的??

這是第二次發生在我身上, 我真的完全不知道為甚麼. 我想也許是一個錯誤stl還是甚麼? 上次發生時, 我真的又列印了同一個檔案, 結果完美了. 歡迎任何建議

讓我們為清理這個需要的努力默哀一分鐘. 撕掉所有樹脂. 撕裂我的建築板. 安息吧. 去除這個沒用的樹脂需要很大的力量.

· 查看原文 · 為此翻譯評分

Ricardo Contreras
2020-02-28 07:53:58

Ricardo Contreras
2020-02-28 07:55:37

Gabi Ras
2020-02-28 07:57:22

Jarin Udom
2020-02-28 08:04:10

James Swan
2020-02-28 08:04:34

Gabi Ras
2020-02-28 08:06:01

Gabi Ras
2020-02-28 08:07:10

Ky Lane
2020-02-28 08:07:37

Jarin Udom
2020-02-28 08:08:32

Ky Lane
2020-02-28 08:08:58

Ky Lane
2020-02-28 08:09:24

Grant Weaver
2020-02-28 08:11:53

Benjamin Brigance
2020-02-28 08:12:08

Nemanja Lacedaemon Enomotarch Đe
2020-02-28 08:16:47

Neil Forster
2020-02-28 08:41:11

Sean Smith
2020-02-28 12:08:49

Sean Smith
2020-02-28 12:10:45

Jason Willis
2020-02-28 12:21:13

Gonzalo Avilez Iglecias
2020-02-28 12:45:10

Gabi Ras
2020-02-28 15:48:53

Gabi Ras
2020-02-28 15:50:53

Benjamin Brigance
2020-02-28 15:53:55

Adrian Petre
2020-03-01 00:52:16


原文網址 Gabi Ras
2020-02-02 18:43:25

I want to change the FEP but I have a big problem: these 2 screws are stuck! How do I remove them??

翻譯年糕

Zena Andreou
2020-02-02 18:46:48

Jose Sicairos
2020-02-02 18:47:06

Tamas Tokai
2020-02-02 18:48:20

Edward Sanders
2020-02-02 18:52:14

Gabi Ras
2020-02-02 18:55:45

Miroslav Zajíček
2020-02-02 19:11:10

Michael A Miller
2020-02-02 20:31:21

Neil Castle
2020-02-02 20:33:34

Kovács János
2020-02-02 20:43:25

Hoghead Hoffer
2020-02-02 20:52:31

Jeffery Nelson
2020-02-02 20:58:46

Gabi Ras
2020-02-02 21:47:37

Gabi Ras
2020-02-02 21:48:42

Gabi Ras
2020-02-02 21:55:15

Gabi Ras
2020-02-02 21:57:41

Gabi Ras
2020-02-02 21:57:58

Tiernan Messmer
2020-02-02 22:06:08

Bart Wilbers
2020-02-02 22:16:23

Gabi Ras
2020-02-02 22:22:16

Jerry Little
2020-02-02 23:47:17

Angelo Apostolou
2020-02-03 02:43:12

Angus Sanders
2020-02-03 04:42:06

Kim Deene
2020-02-03 05:51:54

James Hendrix
2020-02-03 06:40:13

Lou Steinritz
2020-02-03 09:58:55

Om Buncit
2020-02-03 10:48:59

Claudio Campanella
2020-02-03 12:20:07

Paul Tyer
2020-02-03 15:00:27

Ivan Fdc
2020-02-03 21:02:54


原文網址 Gabi Ras
2020-01-21 05:47:59

This has probably been asked before: can I use Elegoo FEP for my anycubic?? They are much much cheaper!!

翻譯年糕

Melecio Guzman
2020-01-21 05:52:35

Gabi Ras
2020-01-21 05:58:30

Gabi Ras
2020-01-21 05:59:59

Melecio Guzman
2020-01-21 06:04:40

Melecio Guzman
2020-01-21 06:07:04

Gabi Ras
2020-01-21 06:08:11

Melecio Guzman
2020-01-21 06:11:13


原文網址 Gabi Ras
2019-12-20 17:20:47

Is there an EU reseller for PolyJuice resin? Shipping from filaments.ca to the Netherlands starts from $40 ?

翻譯年糕

Tim Blom
2019-12-20 18:37:36

Sjef Blaster
2019-12-20 19:04:05

Gabi Ras
2019-12-20 19:12:55

Tim Blom
2019-12-20 19:31:54

Tim Blom
2019-12-20 19:33:11

Gabi Ras
2019-12-20 19:57:09

Tim Blom
2019-12-20 21:59:37

Gabi Ras
2019-12-21 03:42:23


原文網址 Gabi Ras
2019-10-18 18:11:10

May I present you this miniature snow globe. All parts except the dome were printed with the photon S and then painted with enamel paint.

翻譯年糕

Neil Ramsay
2019-10-18 18:50:48

Jason Odegard
2019-10-18 18:55:13

Gabi Ras
2019-10-18 19:02:43

Neil Ramsay
2019-10-18 19:06:42

Ian Chess
2019-10-18 19:09:52

Jim Murphy
2019-10-18 19:19:19

Andrew McBrearty
2019-10-18 20:23:23

Sam Davey
2019-10-18 20:58:46

Derek Reihe
2019-10-18 21:30:32

Jarrod Smith
2019-10-18 22:01:03

Ekaterina Vitalyevna
2019-10-18 22:29:32

Thanos Panagiotaros
2019-10-18 23:28:46

Michael Wang
2019-10-19 02:22:52

Jason Odegard
2019-10-19 03:10:06

Josh N Bee
2019-10-19 03:17:10

Gabi Ras
2019-10-19 03:48:05

Gabi Ras
2019-10-19 03:48:36

Gabi Ras
2019-10-19 03:49:24

Alison Friedlander
2019-10-19 08:15:41

Tom Leech
2019-10-19 08:19:22

Gabi Ras
2019-10-19 16:36:14

Alison Friedlander
2019-10-19 19:33:20

Gabi Ras
2019-10-19 22:30:14

Chris Gough
2019-10-20 04:59:35

Gregorey Savieo
2019-10-20 23:45:52

Jessi Kim
2019-10-24 15:06:46

Robert Daubar
2019-10-24 22:43:12


原文網址 Gabi Ras
2019-10-03 23:21:45

I need to paint a really tiny 3D printed house for a miniature I am working on. I'm talking 6x6 mm with 1 mm windows.
What kind of paint do you use? and what kind of brushes?

I am afraid to put primer on it because it would get rid of detail. I tried with enamel paint but didn't like the results much. I would like some paint that can really get good coverage without leaving streaks.

翻譯年糕

Travis K. Jansen
2019-10-03 23:26:46

Travis K. Jansen
2019-10-03 23:31:38

Travis K. Jansen
2019-10-03 23:33:26

Gabi Ras
2019-10-03 23:38:52

Niall Forrester
2019-10-03 23:42:33

Gabi Ras
2019-10-03 23:46:21

Dan Cowan
2019-10-03 23:49:27

Gabi Ras
2019-10-03 23:50:53

Dan Cowan
2019-10-03 23:51:24

Dan Cowan
2019-10-03 23:52:14

Travis K. Jansen
2019-10-03 23:53:43

Sherri Johnson
2019-10-03 23:54:50

Gabi Ras
2019-10-04 00:02:21

Neil Ramsay
2019-10-04 00:04:50

Sherri Johnson
2019-10-04 00:10:02

Melecio Guzman
2019-10-04 00:23:13

Melecio Guzman
2019-10-04 00:29:07

Travis K. Jansen
2019-10-04 00:41:40

Melecio Guzman
2019-10-04 00:43:36

Victoria L. Cordone
2019-10-04 01:01:41

Erik Brown
2019-10-04 01:48:52

Gabi Ras
2019-10-04 02:11:15

Erik Brown
2019-10-04 02:11:55

Gabi Ras
2019-10-04 02:31:50

Travis McGeathy
2019-10-04 02:45:34

Erik Brown
2019-10-04 02:48:58

Erik Brown
2019-10-04 02:49:26

Erik Brown
2019-10-04 02:50:06

David Dorsett
2019-10-04 03:28:17

Jason Saiter
2019-10-04 03:52:15

Gabi Ras
2019-10-04 04:08:10

Erik Brown
2019-10-04 04:45:03

Gabi Ras
2019-10-04 04:45:40

Erik Brown
2019-10-04 04:49:22

James Richmond
2019-10-04 08:37:45

David Dorsett
2019-10-04 10:02:52

David Dorsett
2019-10-04 10:03:35

Gabi Ras
2019-10-04 17:58:54

Michael Finbarr-Smith
2019-10-04 18:07:58

Gabi Ras
2019-10-04 18:55:01

Michael Finbarr-Smith
2019-10-04 20:00:11

Erik Brown
2019-10-04 21:39:22

Gabi Ras
2019-10-04 22:41:06

Eric Green
2019-10-04 23:07:20

Gabi Ras
2019-10-04 23:50:01


原文網址 Gabi Ras
2019-09-16 04:20:08

Today some really strange lines appeared on my print. I turned out to be a slicing issue in Chitubox. Even though the sliced full image looks good, when you go through it layer by layer you see the lines. Anyone knows why these are caused during slicing? Is it because of my STL file?

翻譯年糕

Joshua Collins
2019-09-16 04:39:32

Davoud Taghawi-Nejad
2019-09-16 05:06:39

Robert James
2019-09-16 16:30:13


原文網址 Gabi Ras
2019-08-27 23:43:56

First results with the plant-based Anycubic resin on the S. Don't mind the back, I'm still learning how to place supports. Overall nice settings but I think they can be optimized for greater detail. The figure is 5 cm in height. I am thinking about increasing the exposure time a bit.

Color: macaroon pink
Layer height: 0.05
Normal exposure time: 16
Off time: 1
Bottom exposure: 60
Bottom layers: 8

翻譯年糕

Mark Wardle
2019-08-27 23:46:02

Gabi Ras
2019-08-27 23:57:39


 

討論主題

全不選 常用關鍵字